Tags

, ,

Today, I’s like to share about making something more adventurously jaw-wrecking : The Gauntlet.

209030229_5319a5b948

Some of the sexiest things once could “easily” try out and make…. well, it’s the easiest thing if you’re into making a full set of armour.

If you’re an aspiring armoursmith starting out(as I), then consider making yourself a pair of hand armours.

 

Disclaimer: You know the drill, I’m not accounted for anything funny you do with your creation whatsoever. Now, grab a hammer and start pounding.

 

Starting out

Now, the reason to start off with gauntlets is simple, there is absolutely less material required to begin, and alot to learn from metalworks with a reasonable effort required to finish your project, plus it has more appeal to incentivize you to strive on. (You need a forge to make breastplate, shoulder armours are not as interesting to make for a 1st try, you can’t slap someone with leg greaves properly).

Gauntlet

Classical duel acceptance 101, Robin Hood: Men In Tights, every armourer should watch it.

Basically:

  • Less material to work with, you just need at least a 60cmx30cm metal sheet
  • You don’t need a forge (yet)
  • A more fun-ctional(if it makes sense) armour to play with
  • You learn the necessity of in-depth metalworks(riveting, etc)
  • Making a nice looking gauntlet is not easy, you’ll need alot of practise to refine it, and you’ll learn alot from the journey

Due to constraints from absurd laws in my country, I am unable to acquire a forge through normal means, and have to resort through sheet metal.

Just remember that it takes a LONG time to make it if you’re starting out.

Materials(Sheet metal)

As a historical Accuracy Buff myself, I do loathe the sense of going down to “costume-grade”, but as one starting out, Armoursmithing is not easy, even with modern tech, I would recommend Aluminum sheets to start out.

  • Aluminum has some distinct advantages: It does not rust, is lightweight, easy to mould and bend but still retains metal strength. Also, aluminum is quite shiny.
  • Mild steel is definitely tougher than Al, but does rust easily, and since it’s harder than aluminum, it’s more dangerous to work with, so take note. Also, Historically accurate.
  • Galvanized Steel is, I might highlight this, DANGEROUS. Any contact with high heat would release zinc oxide, a gas POISONOUS to us, not recommended, even if it rusts less than mild steel. If you don’t intend to use this in a forge, well, ok then. Just be mindful of the smell that lingers onto anything it rubs on.
  • Stainless Steel is a duck to work with, firstly, it’s the HARDEST to cut, is slightly more brittle than other steels, and almost impossible to mould. However, if you do know how, I would recommend this if you’re insane or like a challenge since it almost replicate the properties of historical steel and does not rust. Shinier than mild steel.
  • I’ve rarely worked on brass, but I believe it’s equivalent to the strength of aluminum. Does give a shine with it’s gold colour, but I’ve heard that it will lose its shine after some time.

For the thickness of sheet metals, start off with 18 gauge(I go by SWG for gauges) metal. 20 Gauge is the thinnest you can go if weight is of concern but any thinner would be too flimsy. For historically accurate ones, it would be 16-14 gauges.

  Materials(Leather Gloves)

A must to mould onto your hands, Gauntlets are not a piece by themselves, but rather an attachment to a leather glove, that is either sewn or riveted onto. Getting a good glove is not cheap if you plan to start out.

Just note that it REQUIRES a non-stretchable glove to work. You need the cutout holes to be consistent or your metals will fall apart.

Materials(Rivets)

So far, I’m not aware how rivets were done historically, but there are two types of manual riveting, hot riveting(requires a forge) and cold riveting (just hammering it down). I believe that hot riveting is required for stronger metals like steel, whilst cold riveting can be done on aluminum or brass.

You’ll need alot of rivets to connect your metal pieces together, since it’s essentially one of the few methods of holding metals tightly.

2000px-Riveting.svg

A cold riveting method, best used for softer metals

For this tutorial I’ll be using aluminum rivets specially designed for cold riveting.

Optional Materials(Leather Strips)

Leather strips the length and size of your four fingers is essential if you’d prefer an easier time to work with riveting the metal onto. The strips are placed on top of the glove which only the first and the last finger plating(usually) are riveted together with the strip and the glove itself. The rest of the finger plates can be riveted on the strip itself.

You can do without it, but I believe the strips helps to keep the pieces in line.

Optional Materials(Template reference)

This tutorial does not provide a template, so you’ll have to scour for your own online. Do take note that I’m following a specific template, so you’ll have to make a bit of tweaking if your’s is different.

Depending on what template you’ve got, you’ll always have the plates for all fingers and thumb, the kunckleplate, the plates at the back of the hand, and optionally a vembrace for that complete look.

  Tools

  • (PPE for SAFETY) Gloves and googles: A must if you like a pleasant time. Flying metal shards is not funny either.
  • Ball peen Hammer: A definite must if you would need to hammer your gauntlet into a sexier, curvier look. Also does a good makeshift anvil if you lack one. Just secure it in place on a vice to have your ‘anvil’ ready
  • Another hammer: For obvious reasons
  • Metal Snips: Do note that there are many different types of snips (Left, Right, Centre, Long-Cut) due to difficulty in working with metal
  • Leather Puncher: You’ll need it to cleanly cut out leather gloves
  • Files or a belt sender: You’ll need to smooth out those edges, cut sheets ARE SHARP. Files work fine, but an electric belt sander works wonders.
  • Awls: It’s a sharp needle tool used to mark on metals. Required to draw out templates onto metal sheets
  • Cordless Battery Drill: To drill out holes on your metal sheets, do not use powered drills, that’s overkill.
  • Blocks of wood: For the drilling of holes
  • Strong metal pipe flattener jig: All you need is a half pipe and another smaller pipe
  • A long metal pipe: To shape the rest of the metal pieces.
  • Metal Ruler: To measure your cut out metal parts.

20151025_152959

All you need for the jig. It’s that simple

20151101_125239

Left to right, Metal ruler, Awl, File, Claw Hammer, Ball-peen Hammer, Metal Snips(Straight, Right, and left), Wood Block, Leather Puncher

  Steps

  1. To start off, you’ll need a template to cut off the metal pieces for your gauntlet. You can measure the circumference of your hand and get references from gauntlets online.
  2. Once you obtained the templates, mark them on a piece of cardboard or paper, cutout the pieces, and use the awl along with the pieces and mark on your metal sheets. I’ve used Aluminum sheets for my attempt.
  3. Once marked, bring out your snips and cut along the markings, be sure to leave out an extra 2-3mm of metal as you’ll need to file/sand it down smoothly.
  • NOTE: Metal sheets when cut are EXTREMELY SHARP. Be sure to don gloves before handling them for filing/sanding. Dispose all metal shards in a proper container.

20151015_183313

Be careful of the shards.

4. Once done, assemble your metal pieces for sanding/filing. Remove the sharp nicks and edges made to ensure that your pieces are safe to handle.

20151022_205357

Get those curves right.

5. Once done, it’s time to bend the pieces that will fit into your hand. You’ll need a metal bending jig that consists of strong metal pipes. A half-pipe to collect the piece, and a full pipe to form the metal in shape. Do take note that this applies only to the finger plates. For the hand pieces, you’ll need to find a longer metal pipe to shape it around.

20151025_152951

It’s like kneading bread

6. For the rest of the metal pieces, use a longer, bigger metal pipe to shape them around. Since the pieces are bigger there is no need of a jig for that.

7. If you like, you can give your gloves some depth with a ball-peen hammer. The round side of the hammer can make spherical shapes that’s commonly seen in medieval gauntlets.

8. Once all your pieces are shaped, we’ll move onto riveting the pieces on the leather glove. You’ll need a leather punch to ‘poke’ through the gloves and forming holes for your rivets to work on, and a drill to make holes in the metal pieces. Just be sure that you’re drilling on a wooden block if you like your workbench very much.

  • Note: When drilling on metal, be sure to have a firm grip on the metal pieces, they will fling out of control with the drill.

20151027_152312

Make sure the hole is smaller than the rivet, in order to ensure a tight fit from the rivets…. I seem to be making too many unintentional jokes.

9. If you’re using leather strips, cutting holes on both ends of the leather is enough to hold the metal pieces tight. If you’re not, you’ll have to punch every hole on each piece embedded onto the glove.

20151027_160038

If you’re not, you’ll have to punch every hole on each piece embedded onto the glove.

10. Repeat on the other fingers, and the thumbs of course.

20151028_193945

Shiny stuff. I love this step.

11. Once the finger (and thumb) pieces are done, we’ll move on to the next part, the hand. Depending on the template that you have, you will have about 4-7 pieces of metal plates that will fit snugly onto your hand. Drill holes and rivet those together on the sides to compile them together.

20151029_150256

You’ll need to do abit of manual re-shaping to fit these parts together flawlessly.

12. Once the hand pieces are attached, you’ll have to drill holes and rivet the 4 ends of the pieces (Both upper corners of the first pieces and the lower corners of the last piece) onto the glove,

20151029_162520

That feeling when you are done. Yes, admire it, it’s like your newborn child, goddamnit.

Well, there you have it, a perfectly functional gauntlet. Whilst your first creation might not go as you’d expected, you have fully grasped the concept of making a gauntlet, and you can start forging more elaborate ones if you’re up for game.

Do take note that this is a Work-In-Progress, this isn’t a complete tutorial thus far, I have yet to make my second gauntlet and refine my tutorial. I’ll update this post if I’ve the time to hammer stuff.

Advertisements